Comparing Bi-Radial and Tractrix Horn Dispersion
Dispersion describes how a horn loudspeaker distributes sound around the room. It is more than a simple choice between wide and narrow coverage: the useful question is how rapidly energy becomes concentrated as frequency rises and whether the pattern remains usable from the listening position. A controlled horn can improve clarity and reduce some reflections, yet it can also leave a distant seat poorly served.
Comparing a bi-radial horn with a tractrix horn at different frequencies requires separating mathematical flare behaviour from the finished loudspeaker. Mouth dimensions, crossover point, driver mounting and cabinet shape all alter the result. The profile is therefore a strong predictor, not a complete specification.
What Dispersion Means for a Loudspeaker
Dispersion is usually expressed as the angles over which sound remains within a stated response tolerance. Coverage may be broad at lower frequencies and progressively narrower toward the treble, where wavelengths are short relative to the horn mouth. Horizontal and vertical figures can differ, and a quoted angle rarely says whether the reference point is -6 dB or -10 dB.
Directivity is not the same as tonal neutrality. A horn may control off-axis radiation while introducing its own resonance, diffraction or crossover effects. This is why a specialist builder such as Sunship Audio treats the horn, passive crossover, compression driver, woofer and braced cabinet as one system rather than a collection of interchangeable parts.
The Geometry Behind Each Horn
A tractrix horn follows a mathematical profile derived from the behaviour of an expanding wavefront. Its flare is smooth and progressive, making directivity and loading predictable when the driver, throat and mouth are designed together. The same regularity does not guarantee broad treble coverage, since a modest mouth still behaves as a relatively small source at high frequencies.
A bi-radial horn divides the expansion into two related flare regions, allowing the designer to balance throat loading, mouth size and the rate at which directivity increases. That extra freedom can suit a multi-way system, but the word bi-radial describes no fixed beamwidth. Two designs with the label can differ markedly after mouth aspect ratios, crossover slopes and cabinet integration are applied.
How Directivity Changes with Frequency
Below the horn’s effective lower crossover region, the flare offers little control over where sound goes; the woofer, baffle and room dominate. Through the lower midrange, horn loading organises radiation. In the upper midrange and treble, both families usually become more directional, although the transition depends on scale and crossover design. The ranges below are indicative rather than universal.
| Indicative frequency region | Bi-radial horn | Tractrix horn | Practical consequence |
|---|---|---|---|
| Below roughly 500 Hz | The horn has too little effective size to impose strong directivity, so cabinet and woofer behaviour dominate. | The same basic limit applies despite the mathematically smooth flare. | Room modes, bass placement and cabinet shape become decisive. |
| 500 Hz–1.5 kHz | Directivity becomes more evident, with a carefully chosen two-stage flare supporting a smooth transition. | Progressive expansion produces predictable directivity as the acoustic mouth size becomes significant. | Voice intelligibility and off-axis tonal balance are affected. |
| 1.5–5 kHz | Coverage usually contracts, while vertical and horizontal angles depend on the mouth ratio. | Coverage also contracts because short wavelengths meet a relatively small effective mouth. | Listener position and sibilance become more noticeable. |
| Above 5 kHz | Tight beams are likely unless the mouth is large or the flare is deliberately broad. | Tight beams are equally likely because a smooth profile alone does not widen high-frequency radiation. | Imaging, detail and the usable seating area determine the result. |
A meaningful comparison uses similar mouth areas and crossover points. Otherwise, a large bi-radial horn may appear wider simply because it is larger, while a tractrix horn with an optimised flare may hold a chosen coverage angle better. Published polar plots should therefore be checked for the stated frequency bands and response tolerance.
Vertical and Horizontal Coverage
A circular or symmetrical horn can produce similar patterns in both planes, but a rectangular mouth permits separate control over width and height. Increasing mouth width can improve horizontal reach while leaving vertical coverage tighter; the reverse is also possible. Edge diffraction from the mouth, grille and cabinet then adds smaller variations to the nominal pattern.
In Sydney and Melbourne apartments, placement is often more restrictive than a horn chart suggests. A speaker near a party wall may need controlled directivity aimed into the room, while an open-plan living area may reward broader lateral coverage. Many households now combine hi-fi listening with television and streaming, so consistent dialogue intelligibility at modest evening levels can matter as much as maximum sound pressure.
Crossover, Cabinet and Market Effects
A crossover determines the frequencies at which horn directivity becomes audible, and driver placement affects whether woofer and compression-driver arrivals are aligned. Time-aligned passive networks, rigid mounting and suitable baffle shaping can reduce lobing that otherwise changes off-axis response. A beautiful flare cannot rescue a poorly integrated system, so published measurements from a manufacturer such as CX Acoustics should be compared by method and bandwidth rather than headline figure alone.
Australia’s specialist hi-fi market relies on imported drivers, including TAD-Pioneer units, alongside local cabinetmaking and dealer support. Freight, replacement parts and long-term serviceability can favour established systems over experimental one-offs. Brisbane’s humid subtropical climate also makes stable finishes and well-sealed birch plywood important, since veneer movement and moisture ingress can affect cabinet resonance over time.
Electrical rules matter when horn systems are paired with amplifiers or DIY active crossovers. Equipment sold in Australia must meet applicable electrical-safety and electromagnetic-compatibility requirements associated with the Regulatory Compliance Mark and relevant Australian and New Zealand standards. A passive crossover has no mains-powered supply, but its associated amplifier and any active network still require the appropriate compliance.
Listening Tests and Australian Setup
A comparison becomes useful when it is judged from the intended seat and across several source types. Measurements and listening should address both the axial response and what happens when the listener moves.
A controlled comparison should include:
- Measuring on-axis response and sensitivity before judging beamwidth.
- Comparing vertical and horizontal off-axis response separately.
- Checking crossover phase and the transition through the vocal range.
- Noting whether the sound remains natural from nearby seats.
Installation and household checks should include:
- Measuring room boundaries before deciding on horn orientation.
- Checking amplifier and crossover compliance for the Australian market.
- Accounting for shared-wall noise rules in strata or owners-corporation buildings.
- Allowing for cabinet finish, humidity and long-term service access.
NSW strata schemes can adopt nuisance-noise by-laws under the Strata Schemes Management Act 2019, while Victorian owners corporations operate under the Owners Corporations Act 2022 and building rules. That makes late-night horn output a building issue as well as an acoustic one. The final sound characteristic comes from the interaction of flare, crossover, cabinet, room and listening position, so measured spatial behaviour provides a firmer basis for comparing the two horn families than the profile name alone.