How to calculate equivalent acoustic length for horn crossovers
Equivalent acoustic length gives a designer a compact way to describe the acoustic loading of a horn before choosing passive crossover parts. It is especially useful when the driver, flare, cabinet and listening room are developed as one system, rather than when a compression driver is attached to an existing enclosure. The figure must be tied to a stated definition because physical horn length, internal volume and phase delay are different quantities.
Sunship Audio’s custom loudspeakers illustrate the practical setting: TAD-Pioneer compression drivers and woofers operate behind bi-radial wooden horns with time-aligned passive crossovers and heavily braced birch plywood cabinets. A calculation used in such a system should predict geometry and loading; it cannot replace listening and measurement of the finished pair. Australian builders generally work in millimetres, square metres and hertz.
Why horn geometry changes the crossover
A horn changes the driver’s acoustic load, output and directivity before the signal reaches the crossover network. Its throat controls the air space presented to the compression driver, while its expansion affects low-frequency extension and the distribution of energy. A more strongly flared horn is not automatically better, because it may load the driver differently and produce a less seamless transition with the woofer.
The Australian custom market spans specialist dealers and custom installers in Melbourne, Sydney and Brisbane, where imported premium drivers are often combined with locally made cabinets. A documented calculation gives the builder, installer and customer a common geometric reference before room tuning begins.
For crossover work, equivalent acoustic length serves as an intermediate value. It helps describe the horn’s acoustic loading, but sensitivity, impedance, directivity and phase behaviour still determine the final transition frequency and network.
Define the measurement basis
For crossover calculations, a volume-equivalent definition is transparent. Let (A_t) be the internal throat area, (A(x)) the internal area at axial position (x), and (L_p) the physical horn length. Then:
[ L_{\mathrm{EAL}}=\frac{1}{A_t}\int_0^{L_p}A(x),dx ]
The horn’s internal volume is therefore:
[ V=A_tL_{\mathrm{EAL}} ]
This is the equivalent length of a constant-section passage with the same throat area and internal volume. Some publications use a flare-based equivalent length instead, so the chosen convention should accompany every calculated value.
Measure the throat at the narrowest internal section, not at the driver flange. For a bi-radial horn, local area is the internal width multiplied by height; for a folded horn, calculate volume from unfolded CAD sections while measuring the folded centreline separately for delay estimates. A straight pipe correctly returns its physical length.
Calculate profiles and collect the inputs
For an exponential horn, define the area ratio (R=A_m/A_t), where (A_m) is the mouth area. With (A(x)=A_t e^{2kx}), the flare constant and equivalent length are:
[ k=\frac{\ln R}{2L_p} ]
[ L_{\mathrm{EAL}}=\frac{R-1}{2k}=L_p\frac{R-1}{\ln R} ]
For a straight-sided conical horn, use the throat radius (r_t), mouth radius (r_m) and physical length:
[ L_{\mathrm{EAL}}=L_p\frac{r_m^2+r_mr_t+r_t^2}{3r_t^2} ]
As an example, a 25 mm throat, 300 mm mouth and 500 mm length give an exponential-horn EAL of about 14.4 m and a conical-horn EAL of about 26.2 m. These large figures reflect the small throat area; they do not mean sound physically travels that distance.
The calculation needs two groups of measurements. Record the geometry consistently:
- Internal throat width and height
- Internal mouth width and height
- Physical axial length and profile type
- Width, height and centreline position at intermediate stations
With the geometry established, collect the system data:
- Compression-driver sensitivity and impedance curve
- Horn on-axis response and directivity
- Woofer sensitivity, response and impedance
- Target crossover frequency, slope and listening distance
Apply the result to crossover design
Equivalent acoustic length does not directly set the electrical crossover frequency. The transition occurs where horn and woofer sensitivities intersect, after which the selected slopes determine the network. EAL supplies information about the horn’s effective loading, while measured response shows whether that loading produces useful output near the transition.
For an exponential horn, the estimated waveguide cutoff is (f_c\approx ck/(\pi\sqrt{A_t})). The electrical crossover can sit below this cutoff, as is common when a sensitive compression driver crosses a high-excursion woofer at a much lower frequency. Actual horn efficiency, losses and driver behaviour can shift the usable response.
The crossover calculation resources at CSDWand are useful for checking passive-network arithmetic, but component values still depend on measured impedances. Imported TAD-Pioneer hardware also requires Australian Customs clearance, GST and any applicable duty to be included in the project schedule and budget.
Verify the finished horn in context
Calculated geometry describes an ideal interior, while the fabricated horn determines the result. Wall thickness, timber movement, seams, bends and internal damping all affect its response. Sunship Audio’s bi-radial wooden horns and braced birch-ply cabinets show why cabinet and horn construction must be considered together rather than treated as separate components.
Surface damage can alter both geometry and airflow. Sunship Audio’s guidance on wooden horn dent repair explains why restoration affects acoustic behaviour as well as appearance. A repaired or modified horn should be measured again before the passive crossover is finalised.
Seasonal movement in Sydney and Brisbane, together with Melbourne’s temperature swings, can affect large wooden structures and their seals. Sunship Audio’s listening and demonstration room in Berlin provides a reference environment, but an Australian installation should still be checked in its actual room with the finished cabinet, floor and furniture present.
Compare the available approaches
Each calculation method suits a different horn. The clearest method depends on whether the profile is regular, irregular or available as a fabrication model.
| Method | Required data | Advantage | Limitation |
|---|---|---|---|
| Area integration | Throat, stations and length | Handles irregular shapes | Requires several measurements or CAD data |
| Exponential formula | Throat, mouth and length | Fast for constant-flare horns | Invalid if the profile changes |
| Conical formula | Throat radius, mouth radius and length | Fast for straight-sided horns | Does not account for bends |
| CAD volume | Internal model | Accurate for folded or bi-radial horns | Requires reliable fabrication geometry |
The defensible result is a documented EAL tied to the actual horn geometry, a crossover derived from measured sensitivities and impedances, and a finished system whose response confirms both calculations.